Beginner's Plumbing: What You Need for Bathtub Installation
Beginner's Plumbing: What You Need for Bathtub Installation
Blog Article
What are your thoughts about A Step-by-Step Guide to Installing a Bathtub?
Setting up a tub isn't exactly brain surgery, however it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably challenging task. If the old bathtub is conveniently accessible, the job can relocate immediately; if you need to open a wall surface to get rid of the old bathtub as well as position the new bathtub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will certainly require an assistant to leave the old tub as well as embeded in the brand-new one. Make sure you have actually qualified on your own for the task and are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed job, it is much better to think about utilizing one prior to you start. Chances are you may require an expert plumber to make tube links.
This post will certainly aid you install a brand-new tub in your washroom if you have already gotten a brand-new tub and also don't need to alter the plan of your previous water supply pipes.
Your devices and also product checklist must make up the following:
Planning for the Setup
To start with, the supporting framework provided with the bathroom must be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets system to avoid stress on the bathtub.
Fit the adaptable faucet ports to the bottom of both taps using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final position.
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be rather problematic due to the restricted gain access to that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will come from the pipes. Once the supply pipelines have actually been gotten rid of, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Prior to moving on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Installing the Tub
Using both wooden boards under its feet, put the bath tub in the called for position. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four small factors.
The next goal is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bathtub up until the level reads degree.
To install taps, fit all-time low of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the water as well as inspect all joints and also brand-new pipework for leakages as well as tighten them if necessary. Fill the bathtub and also check the overflow electrical outlet and also the typical electrical outlet for leakages.
Lastly, deal with the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the bath tub ought to wait till the bathtub has actually been made use of a minimum of once as this will certainly settle it into its final placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will require lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washers are in place between the faucet and also the sink. Safeguard the faucet in position with the manufacturer given backnut. When the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap ports. The former kind ought to be connected to the faucet ends first, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath fulfills the tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, creating the water to permeate the wall surface between the bath and the tiling, causing issues with moisture and also possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components and also installations. They are offered in tubes and cartridges, as well as can sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to permit the activity experienced when the bathtub is in use. The sealer can fracture relatively very early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily offered on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that article about Installing A Bathtub from a good friend on another website. So long as you liked our page kindly be sure to share it. I take joy in reading our article about How to Install a Bathtub.
Professional touch for plumbing woes. Report this page